Upvc Tilt and Turn windows

Upvc Tilt and Turn windows

Showing all 22 results



Upvc Tilt & Turn Windows
With their innovative hinge system, Tilt and Turn windows offer added safety and convenience features to the traditional casement window. Incredibly easy to operate, in the ‘Tilt Position’, the top tilts in towards the room to provide enhanced ventilation. In the ‘Turn Position’, the window opens inwards a full 90 degrees, making it suitable as a fire escape exit and also allowing the exterior of the window to be safely and easily cleaned from inside the house.
  •  70mm profile system
  • Features open-in and tilt-in facilities
  • Suitable as a fire escape exit
  • WER ‘A’ ratings with standard double glazing
  • Multi-point locking systems as standard

Quick Upvc Window Installation Guidelines

Remove the old frame

Once the old frame has been removed, brush away any loose debris or cement, leaving a clean opening ready to receive the new frame.

Frame with a cill

If you are fitting a frame with a cill, first decide if you are going to run the cill around the brickwork or cut it Flush to the finished width of the hole (see above). Whichever way you decide to do it, cut the cill to size with a fine toothed saw to fit tightly back to the inside edge where the old frame sat. You may have to remove the tongue of the internal window board first. Once the cill has been cut to size, apply a line of sealant along the cill upstand and across the frame platform at each end. Screw them together, through the bottom frame section along the centre line and into the cill.

Insert new frame

Offer the frame into the opening and using a spirit level, ensure the frame is level, vertical and not twisted before wedging into position.

Affix new frame

Drill through the side of the frame and into the brickwork to a depth just greater than your fixings. Fix firmly without distorting the frame sections, using packers to take up any space between the frame and the brickwork. Make sure that the frame is square by measuring the diagonals. Fixings should be no greater than 600mm apart and 150mm away from any frame joint. Hammer plugs are best, just tap them through the frame, then screw them up with a power driver (just enough to grip firmly, don’t over tighten). Generally the frame heads (tops) and cills are not fixed, however, on wide frames, if you feel the need, make sure you apply a liberal smear of sealant on any fixings that go through the bottom of the frame.

How to glaze the new window

Upvc window glazing fittingStarting with one of the longest beads first, remove the glazing beads by pushing a sharp chisel or a rigid paint scraper between the bead and the frame joint at approximately the centre point. A sharp tap on the butt of the tool should allow the bead to be freed. It is most important to refit the beads in the same positions as they were removed, they may vary in length slightly, due to the  manufacturing process.  Place into position the glass packers approximately 100mm in from each corner (intermediate packers should be used if the double glazed unit is wider than 1200mm). Place the double glazed unit into the frame ensuring correct positioning on the glass packers.  Starting on one of the shortest lengths, fit 3 of the beads moving around the frame using a rubber mallet, finally fitting the last bead by bending it into position. Remember to leave the last bead as a longer length, as it will be easier to bend into the frame.

Toeing and heeling

PVC-U doors and opening windows (sash) are heavy, and although the dead weight is supported on the How to toe and heel a upvc window fittinghinge side when it is opened, there is nothing on the lock side to support the weight, and without the procedure of toeing and heeling the door will drop on the handle side. To prevent a door or sash dropping, the glass or door panel has to be braced diagonally corner to corner by the insertion of plastic packers slipped in the gap between the glass or panel and frame.

The door or sash on the lock side should be raised to the desired height and squared up with the door frame. On the hinge side place the packers at the bottom corner, whilst on the lock side, the packers go at the top (opposite) corner – place a dab of silicone under the packers on the door sides to stop the packers dropping. lt is advisable to use a glazing shovel when lifting the glass or panel. The packers should be placed approximately 150mm from the edge of the frame.

Please contact us through the contact pages or simply email us at info@doorswindowsstairs.co.uk

First Choice at DWS

By continuing to use the site, you agree to the use of cookies. more information

The cookie settings on this website are set to "allow cookies" to give you the best browsing experience possible. If you continue to use this website without changing your cookie settings or you click "Accept" below then you are consenting to this.

Close